 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| FEATURES n n n n n n n n n n n n n n n n n LTC3609 32V, 6A Monolithic Synchronous Step-Down DC/DC Converter DESCRIPTION The LTC(R)3609 is a high efficiency, monolithic synchronous step-down DC/DC converter that can deliver up to 6A output current from a 4V to 32V (36V maximum) input supply. It uses a valley current control architecture to deliver very low duty cycle operation at high frequency with excellent transient response. The operating frequency is selected by an external resistor and is compensated for variations in VIN and VOUT. The LTC3609 can be configured for discontinuous or forced continuous operation at light load. Forced continuous operation reduces noise and RF interference while discontinuous mode provides high efficiency by reducing switching losses at light loads. Fault protection is provided by internal foldback current limiting, an output overvoltage comparator and an optional short-circuit shutdown timer. Soft-start capability for supply sequencing is accomplished using an external timing capacitor. The regulator current limit is user programmable. A power good output voltage monitor indicates when the output is in regulation. The LTC3609 is available in a compact 7mm x 8mm QFN package. 6A Output Current Wide VIN Range = 4V to 32V (36V Maximum) Internal N-Channel MOSFETs True Current Mode Control Optimized for High Step-Down Ratios tON(MIN) 100ns Extremely Fast Transient Response Stable with Ceramic COUT 1% 0.6V Voltage Reference Power Good Output Voltage Monitor Adjustable On-Time/Switching Frequency Adjustable Current Limit Programmable Soft-Start Output Overvoltage Protection Optional Short-Circuit Shutdown Timer Low Shutdown IQ: 15A Available in a 7mm x 8mm 52-Pin QFN Package APPLICATIONS n n Point of Load Regulation Distributed Power Systems L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 5481178, 6100678, 6580258, 5847554, 6304066. TYPICAL APPLICATION High Efficiency Step-Down Converter 187k 0.1F VOUT VON RUN/SS 100pF LTC3609 1.2H SW 1000pF 15.8k ITH SGND BOOST INTVCC FCB VRNG PGOOD EXTVCC PGND VFB 3609 TA01a Efficiency and Power Loss vs Load Current 100 VIN 4V TO 32V 90 80 EFFICIENCY (%) VOUT 2.5V 6A 70 60 50 40 30 10 VIN = 12V VIN = 25V POWER LOSS 100 EFFICIENCY 1000 10000 ION VIN 10F x3 POWER LOSS (mW) 0.22F 100F x2 30.1k 4.7F 20 10 VOUT = 2.5V EXTVCC = 5V 0 0.01 0.1 1 LOAD CURRENT (A) 1 10 3609 TA01b 9.53k 3609f 1 LTC3609 ABSOLUTE MAXIMUM RATINGS (Note 1) PIN CONFIGURATION TOP VIEW 52 PVIN 51 PVIN 50 PVIN 49 PVIN 48 PVIN 47 SW 46 SW 45 SW 44 SW 43 SW 42 SW 41 SW Input Supply Voltage (SVIN, PVIN, ION)....... 36V to -0.3V Boosted Topside Driver Supply Voltage (BOOST) ................................................ 42V to -0.3V SW Voltage ............................................... 36V to -5V INTVCC, EXTVCC, (BOOST - SW), RUN/SS, PGOOD Voltages ...................................... 7V to -0.3V FCB, VON, VRNG Voltages............ INTVCC + 0.3V to -0.3V ITH, VFB Voltages ....................................... 2.7V to -0.3V Operating Junction Temperature Range (Notes 2, 4)........................................ -40C to 125C Storage Temperature Range................... -55C to 125C PVIN 1 PVIN 2 PVIN 3 PVIN 4 PVIN 5 PVIN 6 PVIN 7 SW 8 NC 9 SGND 10 BOOST 11 RUN/SS 12 VON 13 SGND 14 54 SGND 53 PVIN 40 PGND 39 PGND 38 PGND 55 SW 37 PGND 36 PGND 35 PGND 34 PGND 33 SW 32 INTVCC 31 INTVCC 30 SVIN 29 EXTVCC 28 NC 27 SGND VRNG 17 ITH 18 FCB 19 NC 21 ION 22 VFB 23 NC 24 SGND 15 PGOOD 16 SGND 20 NC 25 WKG PACKAGE 52-LEAD (7mm 8mm) QFN MULTIPAD TJMAX = 125C, JA = 29C/W ORDER INFORMATION LEAD FREE FINISH LTC3609EWKG#PBF LTC3609IWKG#PBF TAPE AND REEL LTC3609EWKG#TRPBF LTC3609IWKG#TRPBF PART MARKING* LTC3609WKG LTC3609WKG PACKAGE DESCRIPTION 52-Lead (7mm x 8mm) Plastic QFN 52-Lead (7mm x 8mm) Plastic QFN TEMPERATURE RANGE -40C to 125C -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ SGND 26 3609f 2 LTC3609 ELECTRICAL CHARACTERISTICS SYMBOL Main Control Loop SVIN IQ Operating Input Voltage Range Input DC Supply Current Normal Shutdown Supply Current Feedback Reference Voltage ITH = 1.2V (Note 3) -40C to 85C -40C to 125C VIN = 4V to 30V, ITH = 1.2V (Note 3) ITH = 0.5V to 1.9V (Note 3) VFB = 0.6V ITH = 1.2V (Note 3) VFCB = 0.6V ION = 60A, VON = 1.5V ION = 60A, VON = 0V ION = 180A, VON = 0V ION = 30A, VON = 1.5V VRNG = 0V, VFB = 0.56V, FCB = 0V VRNG = 1.2V, VFB = 0.56V, FCB = 0V VRNG = 0V, VFB = 0.64V, FCB = 0V VRNG = 1.2V, VFB = 0.64V, FCB = 0V l l l l l The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C. VIN = 15V unless otherwise noted. PARAMETER CONDITIONS MIN 4 900 15 0.594 0.590 0.600 0.600 0.002 -0.05 -5 1.4 0.54 220 1.7 0.6 -1 280 110 60 320 4 6 2 4 7 0.8 RUN/SS Pin Rising RUN/SS Pin Falling VRUN/SS = 0V VRUN/SS = 4.5V, VFB = 0V VIN Falling VIN Rising l l TYP MAX 32 2000 30 0.606 0.610 UNITS V A A V V %/V VFB l VFB(LINEREG) VFB(LOADREG) IFB gm(EA) VFCB IFCB tON tON(MIN) tOFF(MIN) IVALLEY(MAX) IVALLEY(MIN) VFB(OV) VRUN/SS(ON) VRUN/SS(LE) VRUN/SS(LT) IRUN/SS(C) IRUN/SS(D) VIN(UVLO) VIN(UVLOR) RDS(ON) Feedback Voltage Line Regulation Feedback Voltage Load Regulation Feedback Input Current Error Amplifier Transconductance Forced Continuous Threshold Forced Continuous Pin Current On-Time Minimum On-Time Minimum Off-Time Maximum Valley Current Maximum Reverse Valley Current Output Overvoltage Fault Threshold RUN Pin Start Threshold RUN Pin Latchoff Enable Threshold RUN Pin Latchoff Threshold Soft-Start Charge Current Soft-Start Discharge Current Undervoltage Lockout Undervoltage Lockout Release Top Switch On-Resistance Bottom Switch On-Resistance -0.3 50 2 0.66 -2 340 100 500 % nA mS V A ns ns ns ns A A 9 14 4 7 10 1.5 4 3.5 6 10 13 2 4.5 4.2 -3 3 3.9 4 27 22 A A % V V V A A V V m m -0.5 0.8 -1.2 1.8 3.4 3.5 18 13 3609f 3 LTC3609 ELECTRICAL CHARACTERISTICS SYMBOL VINTVCC VLDO(LOADREG) VEXTVCC VEXTVCC VEXTVCC(HYS) PGOOD Output VFBH VFBL VFB(HYS) VPGL PGOOD Upper Threshold PGOOD Lower Threshold PGOOD Hysteresis PGOOD Low Voltage VFB Rising VFB Falling VFB Returning IPGOOD = 5mA 7 -7 10 -10 1 0.15 13 -13 2.5 0.4 % % % V PARAMETER Internal VCC Voltage Internal VCC Load Regulation EXTVCC Switchover Voltage EXTVCC Switch Drop Voltage EXTVCC Switchover Hysteresis Internal VCC Regulator 6V < VIN < 30V, VEXTVCC = 4V ICC = 0mA to 20mA, VEXTVCC = 4V ICC = 20mA, VEXTVCC Rising ICC = 20mA, VEXTVCC = 5V l l The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C. VIN = 15V unless otherwise noted. CONDITIONS MIN 4.7 4.5 TYP 5 -0.1 4.7 150 500 300 MAX 5.5 2 UNITS V % V mV mV Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: TJ is calculated from the ambient temperature TA and power dissipation PD as follows: TJ = TA + (PD * 29C/W) (JA is simulated per JESD51-7 high effective thermal conductivity test board). JC = 1C/W (JC is simulated when heat sink is applied at the bottom of the package). Note 3: The LTC3609 is tested in a feedback loop that adjusts VFB to achieve a specified error amplifier output voltage (ITH). The specification at 85C is not tested in production. This specification is assured by design, characterization, and correlation to testing at 125C. Note 4: The LTC3609E is guaranteed to meet performance specifications from 0C to 125C. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3609I is guaranteed over the -40C to 125C operating junction temperature range. TYPICAL PERFORMANCE CHARACTERISTICS Transient Response VOUT 200mV/DIV VOUT 200mV/DIV Transient Response (Discontinuous Mode) Start-Up RUN/SS 2V/DIV IL 5A/DIV ILOAD 5A/DIV 20s/DIV LOAD STEP 0A TO 5A VIN = 25V VOUT = 2.5V FCB = 0V FIGURE 6 CIRCUIT 3609 G01 IL 5A/DIV ILOAD 5A/DIV 20s/DIV LOAD STEP 1A TO 6A VIN = 25V VOUT = 2.5V FCB = INTVCC FIGURE 6 CIRCUIT 3609 G02 VOUT 1V/DIV IL 5A/DIV 40ms/DIV VIN = 12V VOUT = 2.5V RLOAD = 0.5 FIGURE 6 CIRCUIT 3609 G03 3609f 4 LTC3609 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency vs Load Current 100 90 80 EFFICIENCY (%) EFFICIENCY (%) 70 60 50 40 30 20 10 VIN = 12V FREQUENCY = 550kHz 0 0.1 1 0.01 LOAD CURRENT (A) VOUT = 5V VOUT = 3.3V VOUT = 2.5V VOUT = 1.8V VOUT = 1.5V VOUT = 1.2V VOUT = 1V 95 FREQUENCY (kHz) 100 Efficiency vs Input Voltage FCB = 5V FIGURE 6 CIRCUIT 650 Frequency vs Input Voltage 600 ILOAD = 6A 550 90 ILOAD = 6A 500 ILOAD = 1A FCB = 0V FIGURE 6 CIRCUIT 5 8 11 14 17 20 23 26 29 32 INPUT VOLTAGE (V) ILOAD = 1A 85 450 80 10 3609 G04 400 5 8 11 14 17 20 23 26 INPUT VOLTAGE (V) 29 32 3609 G05 3609 G06 Frequency vs Load Current 700 600 FREQUENCY (kHz) 500 400 300 DISCONTINUOUS MODE 200 100 0 0 2 4 6 LOAD CURRENT (A) 8 3609 G07 Load Regulation 0.80 FIGURE 6 CIRCUIT 2.5 0.60 2.0 0.40 VOUT (%) 0.20 0 ITH VOLTAGE (V) 1.5 ITH Voltage vs Load Current FIGURE 6 CIRCUIT CONTINUOUS MODE CONTINUOUS MODE 1.0 -0.20 -0.40 -0.60 -0.80 0 2 4 6 LOAD CURRENT (A) 8 3609 G08 0.5 DISCONTINUOUS MODE 0 2 4 6 LOAD CURRENT (A) 8 3609 G09 0 Load Current vs ITH Voltage at Different VRNG 15 VRNG = 1.2V 10 LOAD CURRENT (A) ON-TIME (ns) 10000 On-Time vs ION Current VVON = 0V 1000 On-Time vs VON Voltage ION = 30A 800 ON-TIME (ns) VRNG = 0.7V 1000 5 600 0 VRNG = 1V 400 100 200 -5 -10 0 0.5 1.0 1.5 ITH VOLTAGE (V) 2.0 2.5 3609 G10 10 1 10 ION CURRENT (A) 100 3609 G11 0 0 1 2 VON VOLTAGE (V) 3 3609 G12 3609f 5 LTC3609 TYPICAL PERFORMANCE CHARACTERISTICS On-Time vs Temperature 300 250 200 150 100 50 0 -50 -25 MAXIMUM VALLEY CURRENT LIMIT (A) IION = 30A VVON = 0V 15 Maximum Valley Current Limit vs VRNG Voltage MAXIMUM VALLEY CURRENT LIMIT (A) 1.1 1.2 3609 G14 Maximum Valley Current Limit vs RUN/SS Voltage 15 FIGURE 6 CIRCUIT FIGURE 6 CIRCUIT 12 12 ON-TIME (ns) 9 9 6 6 3 3 0 50 25 75 TEMPERATURE (C) 100 125 0 0.5 0.6 0.7 0.8 0.9 1.0 VRNG VOLTAGE (V) 0 1.65 1.90 2.15 2.40 2.65 2.90 3.15 3.40 RUN/SS VOLTAGE (V) 3609 G15 3609 G13 Maximum Valley Current Limit vs Temperature 15 MAXIMUM VALLEY CURRENT LIMIT (A) MAXIMUM VALLEY CURRENT (A) 10 Maximum Valley Current vs Input Voltage 10 MAXIMUM VALLEY CURRENT LIMIT (A) Maximum Valley Current Limit in Foldback 12 8 8 9 6 6 6 4 4 3 2 2 0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 0 0 4 12 20 28 INPUT VOLTAGE (V) 36 3609 G17 0 0.1 0.2 3609 G16 0.3 VFB (V) 0.4 0.5 0.6 3609 G18 Feedback Reference Voltage vs Temperature 0.62 FEEDBACK REFERENCE VOLTAGE (V) 2.0 Error Amplifier gm vs Temperature 1400 1200 INPUT CURRENT (A) Input and Shutdown Currents vs Input Voltage 40 EXTVCC OPEN 35 SHUTDOWN CURRENT (A) 30 25 800 SHUTDOWN 600 15 400 200 EXTVCC = 5V 10 5 0 0 5 15 10 20 INPUT VOLTAGE (V) 25 30 3609 G21 0.61 gm (mS) 1.8 1000 1.6 0.60 20 1.4 0.59 1.2 0.58 -50 -25 75 0 25 50 TEMPERATURE (C) 100 125 1.0 -50 0 -25 50 25 0 75 TEMPERATURE (C) 100 125 3609 G19 3609 G20 3609f 6 LTC3609 TYPICAL PERFORMANCE CHARACTERISTICS INTVCC Load Regulation 0.30 EXTVCC SWITCH RESISTANCE () 0.20 0.10 INTVCC (%) 0 10 EXTVCC Switch Resistance vs Temperature 25 IEXTVCC vs Frequency VIN = 24V 8 IEXTVCC (mA) 0 50 75 25 TEMPERATURE (C) 100 125 20 6 15 -0.10 -0.20 -0.30 -0.40 4 10 2 5 0 40 10 20 30 INTVCC LOAD CURRENT (mA) 50 3609 G22 0 -50 -25 0 400 500 600 700 800 FREQUENCY (kHz) 900 1000 3609 G28 3609 G23 FCB Pin Current vs Temperature 0 -0.25 RUN/SS PIN CURRENT (A) FCB PIN CURRENT (A) -0.50 -0.75 -1.00 -1.25 -1.50 -50 -25 3 RUN/SS Pin Current vs Temperature 5.0 RUN/SS Pin Current vs Temperature RUN/SS PIN CURRENT (A) 2 PULL-DOWN CURRENT 1 4.5 LATCHOFF ENABLE 4.0 0 3.5 LATCHOFF THRESHOLD -1 PULL-UP CURRENT 0 50 25 75 TEMPERATURE (C) 100 125 -2 -50 -25 0 50 75 25 TEMPERATURE (C) 100 125 3.0 -50 -25 75 0 25 50 TEMPERATURE (C) 100 125 3609 G25 3609 G24 3609 G26 Undervoltage Lockout Threshold vs Temperature UNDERVOLTAGE LOCKOUT THRESHOLD (V) 4.0 Load Step f = 500kHz IL 5A/DIV EFFICIENCY (%) 100 95 Efficiency vs Load Current 3.5 90 85 80 75 70 65 40s/DIV LOAD STEP 1A TO 4A VIN = 24V VOUT = 12V FCB = 0V FIGURE 8 CIRCUIT 3609 G29 DCM 3.0 VOUT 200mV/DIV 2.5 CCM 60 55 50 0.01 VIN = 24V FREQUENCY = 500kHz 10 3609 G30 2.0 -50 -25 75 0 25 50 TEMPERATURE (C) 100 125 3609 G27 0.1 1 LOAD CURRENT (A) FIGURE 8 CIRCUIT 3609f 7 LTC3609 PIN FUNCTIONS PVIN (Pins 1, 2, 3, 4, 5, 6, 7, 48, 49, 50, 51, 52, 53): Main Input Supply. Decouple this pin to power PGND with the input capacitance CIN. SW (Pins 8, 33, 41, 42, 43, 44, 45, 46, 47, 55): Switch Node Connection to the Inductor. The (-) terminal of the bootstrap capacitor CB also connects here. This pin swings from a diode voltage drop below ground up to VIN. NC (Pins 9, 21, 24, 25, 28): No Connection. SGND (Pins 10, 14, 15, 20, 26, 27, 54): Signal Ground. All small-signal components and compensation components should connect to this ground, which in turn connects to PGND at one point. BOOST (Pin 11): Boosted Floating Driver Supply. The (+) terminal of the bootstrap capacitor CB connects here. This pin swings from a diode voltage drop below INTVCC up to VIN + INTVCC. RUN/SS (Pin 12): Run Control and Soft-Start Input. A capacitor to ground at this pin sets the ramp time to full output current (approximately 3s/F) and the time delay for overcurrent latchoff (see Applications Information). Forcing this pin below 0.8V shuts down the device. VON (Pin 13): On-Time Voltage Input. Voltage trip point for the on-time comparator. Tying this pin to the output voltage or an external resistive divider from the output makes the on-time proportional to VOUT. The comparator input defaults to 0.7V when the pin is grounded and defaults to 2.4V when the pin is tied to INTVCC. Tie this pin to INTVCC in high VOUT applications to use a lower RON value. PGOOD (Pin 16): Power Good Output. Open drain logic output that is pulled to ground when the output voltage is not within 10% of the regulation point. VRNG (Pin 17): Current Limit Range Input. The voltage at this pin adjusts maximum valley current and can be set from 0.7V to 1.2V by a resistive divider from INTVCC. It defaults to 0.7V if the VRNG pin is tied to ground which results in a typical 9A current limit. ITH (Pin 18): Current Control Threshold and Error Amplifier Compensation Point. The current comparator threshold increases with this control voltage. The voltage ranges from 0V to 2.4V with 0.8V corresponding to zero sense voltage (zero current). FCB (Pin 19): Forced Continuous Input. Tie this pin to ground to force continuous synchronous operation at low load, to INTVCC to enable discontinuous mode operation at low load or to a resistive divider from a secondary output when using a secondary winding. ION (Pin 22): On-Time Current Input. Tie a resistor from VIN to this pin to set the one-shot timer current and thereby set the switching frequency. VFB (Pin 23): Error Amplifier Feedback Input. This pin connects the error amplifier input to an external resistive divider from VOUT. EXTVCC (Pin 29): External VCC Input. When EXTVCC exceeds 4.7V, an internal switch connects this pin to INTVCC and shuts down the internal regulator so that controller and gate drive power is drawn from EXTVCC. Do not exceed 7V at this pin and ensure that EXTVCC < VIN. SVIN (Pin 30): Supply pin for internal PWM controller. INTVCC (Pins 31, 32): Internal 5V Regulator Output. The driver and control circuits are powered from this voltage. Decouple this pin to power ground with a minimum of 4.7F low ESR tantalum or ceramic capacitor. PGND (Pins 34, 35, 36, 37, 38, 39, 40): Power Ground. Connect this pin closely to the (-) terminal of CVCC and the (-) terminal of CIN. 3609f 8 LTC3609 FUNCTIONAL DIAGRAM RON VON 13 ION 22 FCB 19 4.7V 0.7V 2.4V 1A PVIN EXTVCC 29 SVIN 30 + 0.6V - 0.6V REF 5V REG 1, 2, 3, 4, 5, 6, 7, 48, 49, 50, 51, 52, 53 CIN INTVCC 31, 32 11 BOOST - F VVON tON = (10pF) IION + R S Q FCNT ON M1 CB + ICMP 20k + IREV SWITCH LOGIC SW 8, 33, 41, 42, 43, 44, 45, 46, 47, 55 DB L1 VOUT - 1.4V - SHDN + COUT M2 PGND CVCC OV VRNG 17 (0.5 TO 2) 0.7V 34, 35, 36, 37, 38, 39, 40 16 PGOOD 1 240k Q2 Q4 ITHB Q6 1V UV + - R2 0.54V 23 Q3 Q1 OV VFB R1 + - SS RUN SHDN 1.2A NC 9, 21, 24, 25, 28 6V 0.6V 18 ITH 0.66V SGND 10, 14, 15, 20, 26, 27, 54 + - 0.8V 3.3 EA + - + - - + 0.4V 12 RUN/SS CSS 3609 FD 3609f 9 LTC3609 OPERATION Main Control Loop The LTC3609 is a high efficiency monolithic synchronous, step-down DC/DC converter utilizing a constant on-time, current mode architecture. It operates from an input voltage range of 4V to 32V/36V maximum and provides a regulated output voltage at up to 6A of output current. The internal synchronous power switch increases efficiency and eliminates the need for an external Schottky diode. In normal operation, the top MOSFET is turned on for a fixed interval determined by a one-shot timer OST. When the top MOSFET is turned off, the bottom MOSFET is turned on until the current comparator ICMP trips, restarting the one-shot timer and initiating the next cycle. Inductor current is determined by sensing the voltage between the PGND and SW pins using the bottom MOSFET on-resistance. The voltage on the ITH pin sets the comparator threshold corresponding to inductor valley current. The error amplifier EA adjusts this voltage by comparing the feedback signal VFB from the output voltage with an internal 0.6V reference. If the load current increases, it causes a drop in the feedback voltage relative to the reference. The ITH voltage then rises until the average inductor current again matches the load current. At light load, the inductor current can drop to zero and become negative. This is detected by current reversal comparator IREV which then shuts off M2 (see Functional Diagram), resulting in discontinuous operation. Both switches will remain off with the output capacitor supplying the load current until the ITH voltage rises above the zero current level (0.8V) to initiate another cycle. Discontinuous mode operation is disabled by comparator F when the FCB pin is brought below 0.6V, forcing continuous synchronous operation. The operating frequency is determined implicitly by the top MOSFET on-time and the duty cycle required to maintain regulation. The one-shot timer generates an on-time that is proportional to the ideal duty cycle, thus holding frequency approximately constant with changes in VIN. The nominal frequency can be adjusted with an external resistor RON. Overvoltage and undervoltage comparators OV and UV pull the PGOOD output low if the output feedback voltage exits a 10% window around the regulation point. Furthermore, in an overvoltage condition, M1 is turned off and M2 is turned on and held on until the overvoltage condition clears. Foldback current limiting is provided if the output is shorted to ground. As VFB drops, the buffered current threshold voltage ITHB is pulled down by clamp Q3 to a 1V level set by Q4 and Q6. This reduces the inductor valley current level to one sixth of its maximum value as VFB approaches 0V. Pulling the RUN/SS pin low forces the controller into its shutdown state, turning off both M1 and M2. Releasing the pin allows an internal 1.2A current source to charge up an external soft-start capacitor CSS. When this voltage reaches 1.5V, the controller turns on and begins switching, but with the ITH voltage clamped at approximately 0.6V below the RUN/SS voltage. As CSS continues to charge, the soft-start current limit is removed. INTVCC/EXTVCC Power Power for the top and bottom MOSFET drivers and most of the internal controller circuitry is derived from the INTVCC pin. The top MOSFET driver is powered from a floating bootstrap capacitor CB. This capacitor is recharged from INTVCC through an external Schottky diode DB when the top MOSFET is turned off. When the EXTVCC pin is grounded, an internal 5V low dropout regulator supplies the INTVCC power from VIN. If EXTVCC rises above 4.7V, the internal regulator is turned off, and an internal switch connects EXTVCC to INTVCC. This allows a high efficiency source connected to EXTVCC, such as an external 5V supply or a secondary output from the converter, to provide the INTVCC power. Voltages up to 7V can be applied to EXTVCC for additional gate drive. If the input voltage is low and INTVCC drops below 3.5V, undervoltage lockout circuitry prevents the power switches from turning on. 3609f 10 LTC3609 APPLICATIONS INFORMATION The basic LTC3609 application circuit is shown on the front page of this data sheet. External component selection is primarily determined by the maximum load current. The LTC3609 uses the on-resistance of the synchronous power MOSFET for determining the inductor current. The desired amount of ripple current and operating frequency also determines the inductor value. Finally, CIN is selected for its ability to handle the large RMS current into the converter and COUT is chosen with low enough ESR to meet the output voltage ripple and transient specification. VON and PGOOD The LTC3609 has an open-drain PGOOD output that indicates when the output voltage is within 10% of the regulation point. The LTC3609 also has a VON pin that allows the on-time to be adjusted. Tying the VON pin high results in lower values for RON which is useful in high VOUT applications. The VON pin also provides a means to adjust the on-time to maintain constant frequency operation in applications where VOUT changes and to correct minor frequency shifts with changes in load current. VRNG Pin and ILIMIT Adjust The VRNG pin is used to adjust the maximum inductor valley current, which in turn determines the maximum average output current that the LTC3609 can deliver. The maximum output current is given by: IOUT(MAX) = IVALLEY(MAX) + 1/2 IL, The IVALLEY(MAX) is shown in the figure "Maximum Valley Current Limit vs VRNG Voltage" in the Typical Performance Characteristics. An external resistor divider from INTVCC can be used to set the voltage on the VRNG pin from 0.7V to 1.2V, or it can be simply tied to ground force a default value equivalent to 0.7V. When setting current limit, ensure that the junction temperature does not exceed the maximum rating of 125C. Do not float the VRNG pin. Operating Frequency The choice of operating frequency is a tradeoff between efficiency and component size. Low frequency operation improves efficiency by reducing MOSFET switching losses but requires larger inductance and/or capacitance in order to maintain low output ripple voltage. The operating frequency of LTC3609 applications is determined implicitly by the one-shot timer that controls the on-time tON of the top MOSFET switch. The on-time is set by the current into the ION pin and the voltage at the VON pin according to: tON = VVON (10pF) IION Tying a resistor RON from VIN to the ION pin yields an on-time inversely proportional to VIN. The current out of the ION pin is: IION = VIN RON For a step-down converter, this results in approximately constant frequency operation as the input supply varies: f= VOUT [ HZ ] VVON RON(10pF) To hold frequency constant during output voltage changes, tie the VON pin to VOUT or to a resistive divider from VOUT when VOUT > 2.4V. The VON pin has internal clamps that limit its input to the one-shot timer. If the pin is tied below 0.7V, the input to the one-shot is clamped at 0.7V. Similarly, if the pin is tied above 2.4V, the input is clamped at 2.4V. In high VOUT applications, tying VON to INTVCC so that the comparator input is 2.4V results in a lower value for RON. Figures 1a and 1b show how RON relates to switching frequency for several common output voltages. 3609f 11 LTC3609 APPLICATIONS INFORMATION 1000 VOUT = 3.3V VOUT = 1.5V VOUT = 2.5V 100 100 1000 RON (k) 10000 3609 F01a load current increases. By lengthening the on-time slightly as current increases, constant frequency operation can be maintained. This is accomplished with a resistive divider from the ITH pin to the VON pin and VOUT. The values required will depend on the parasitic resistances in the specific application. A good starting point is to feed about 25% of the voltage change at the ITH pin to the VON pin as shown in Figure 2a. Place capacitance on the VON pin to filter out the ITH variations at the switching frequency. The resistor load on ITH reduces the DC gain of the error amp and degrades load regulation, which can be avoided by using the PNP emitter follower of Figure 2b. Minimum Off-time and Dropout Operation The minimum off-time tOFF(MIN) is the smallest amount of time that the LTC3609 is capable of turning on the bottom MOSFET, tripping the current comparator and turning the MOSFET back off. This time is generally about 250ns. The minimum off-time limit imposes a maximum duty cycle of tON/(tON + tOFF(MIN)). If the maximum duty cycle is reached, due to a dropping input voltage for example, then the output will drop out of regulation. The minimum input voltage to avoid dropout is: Figure 1a. Switching Frequency vs RON (VON = 0V) SWITCHING FREQUENCY (kHz) SWITCHING FREQUENCY (kHz) 1000 VOUT = 12V VOUT = 5V VOUT = 3.3V 100 100 1000 RON (k) 10000 3609 F01b VIN(MIN) = VOUT tON + tOFF(MIN) tON Figure 1b. Switching Frequency vs RON (VON = INTVCC) A plot of maximum duty cycle vs frequency is shown in Figure 3. Setting the Output Voltage The LTC3609 develops a 0.6V reference voltage between the feedback pin, VFB, and the signal ground as shown in Figure 6. The output voltage is set by a resistive divider according to the following formula: R2 VOUT = 0.6 V 1+ R1 To improve the frequency response, a feed-forward capacitor, C1, may also be used. Great care should be taken to route the VFB line away from noise sources, such as the inductor or the SW line. Because the voltage at the ION pin is about 0.7V, the current into this pin is not exactly inversely proportional to VIN, especially in applications with lower input voltages. To correct for this error, an additional resistor RON2 connected from the ION pin to the 5V INTVCC supply will further stabilize the frequency. RON2 = 5V RON 0.7 V Changes in the load current magnitude will also cause frequency shift. Parasitic resistance in the MOSFET switches and inductor reduce the effective voltage across the inductance, resulting in increased duty cycle as the 3609f 12 LTC3609 APPLICATIONS INFORMATION RVON1 30k VOUT RVON2 100k CVON 0.01F RC ITH CC VON LTC3609 ripple. Highest efficiency operation is obtained at low frequency with small ripple current. However, achieving this requires a large inductor. There is a tradeoff between component size, efficiency and operating frequency. A reasonable starting point is to choose a ripple current that is about 40% of IOUT(MAX). The largest ripple current occurs at the highest VIN. To guarantee that ripple current does not exceed a specified maximum, the inductance should be chosen according to: VOUT VOUT L= 1- f IL(MAX) VIN(MAX) Once the value for L is known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores. A variety of inductors designed for high current, low voltage applications are available from manufacturers such as Sumida, Panasonic, Coiltronics, Coilcraft and Toko. CIN and COUT Selection (2a) RVON1 3k VOUT INTVCC 10k Q1 2N5087 RVON2 10k CVON 0.01F RC ITH CC 3609 F02 VON LTC3609 (2b) Figure 2. Correcting Frequency Shift with Load Current Changes 2.0 SWITCHING FREQUENCY (MHz) 1.5 DROPOUT REGION 1.0 The input capacitance CIN is required to filter the square wave current at the drain of the top MOSFET. Use a low ESR capacitor sized to handle the maximum RMS current. IRMS IOUT(MAX) VOUT VIN VIN -1 VOUT 0.5 0 0 0.25 0.50 0.75 DUTY CYCLE (VOUT/VIN) 1.0 3609 F03 Figure 3. Maximum Switching Frequency vs Duty Cycle Inductor Selection Given the desired input and output voltages, the inductor value and operating frequency determine the ripple current: V V IL = OUT 1 - OUT VIN f L Lower ripple current reduces core losses in the inductor, ESR losses in the output capacitors and output voltage This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT(MAX)/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that ripple current ratings from capacitor manufacturers are often based on only 2000 hours of life which makes it advisable to derate the capacitor. The selection of COUT is primarily determined by the ESR required to minimize voltage ripple and load step transients. The output ripple VOUT is approximately bounded by: 1 VOUT IL ESR + 8 fCOUT 3609f 13 LTC3609 APPLICATIONS INFORMATION Since IL increases with input voltage, the output ripple is highest at maximum input voltage. Typically, once the ESR requirement is satisfied, the capacitance is adequate for filtering and has the necessary RMS current rating. Multiple capacitors placed in parallel may be needed to meet the ESR and RMS current handling requirements. Dry tantalum, special polymer, aluminum electrolytic and ceramic capacitors are all available in surface mount packages. Special polymer capacitors offer very low ESR but have lower capacitance density than other types. Tantalum capacitors have the highest capacitance density but it is important to only use types that have been surge tested for use in switching power supplies. Aluminum electrolytic capacitors have significantly higher ESR, but can be used in cost-sensitive applications providing that consideration is given to ripple current ratings and long term reliability. Ceramic capacitors have excellent low ESR characteristics but can have a high voltage coefficient and audible piezoelectric effects. The high Q of ceramic capacitors with trace inductance can also lead to significant ringing. When used as input capacitors, care must be taken to ensure that ringing from inrush currents and switching does not pose an overvoltage hazard to the power switches and controller. To dampen input voltage transients, add a small 5F to 50F aluminum electrolytic capacitor with an ESR in the range of 0.5 to 2. High performance through-hole capacitors may also be used, but an additional ceramic capacitor in parallel is recommended to reduce the effect of their lead inductance. Top MOSFET Driver Supply (CB, DB) An external bootstrap capacitor CB connected to the BOOST pin supplies the gate drive voltage for the topside MOSFET. This capacitor is charged through diode DB from INTVCC when the switch node is low. When the top MOSFET turns on, the switch node rises to VIN and the BOOST pin rises to approximately VIN + INTVCC. The boost capacitor needs to store about 100 times the gate charge required by the top MOSFET. In most applications an 0.1F to 0.47F X5R , or X7R dielectric capacitor is adequate. Discontinuous Mode Operation and FCB Pin The FCB pin determines whether the bottom MOSFET remains on when current reverses in the inductor. Tying this pin above its 0.6V threshold enables discontinuous operation where the bottom MOSFET turns off when inductor current reverses. The load current at which current reverses and discontinuous operation begins depends on the amplitude of the inductor ripple current and will vary with changes in VIN. Tying the FCB pin below the 0.6V threshold forces continuous synchronous operation, allowing current to reverse at light loads and maintaining high frequency operation. In addition to providing a logic input to force continuous operation, the FCB pin provides a means to maintain a flyback winding output when the primary is operating in discontinuous mode. The secondary output VOUT2 is normally set as shown in Figure 4 by the turns ratio N of the transformer. However, if the controller goes into discontinuous mode and halts switching due to a light primary load current, then VOUT2 will droop. An external resistor divider from VOUT2 to the FCB pin sets a minimum voltage VOUT2(MIN) below which continuous operation is forced until VOUT2 has risen above its minimum: R4 VOUT 2(MIN) = 0.6 V 1+ R3 Fault Conditions: Current Limit and Foldback The LTC3609 has a current mode controller which inherently limits the cycle-by-cycle inductor current not only in steady state operation but also in transient. To further limit current in the event of a short circuit to ground, the LTC3609 includes foldback current limiting. If the output falls by more than 25%, then the maximum sense voltage is progressively lowered to about one sixth of its full value. INTVCC Regulator and EXTVCC Connection An internal P-channel low dropout regulator produces the 5V supply that powers the drivers and internal circuitry 3609f 14 LTC3609 APPLICATIONS INFORMATION IN4148 VOUT2 CSEC 1F VOUT1 COUT GND SW 40 39 38 37 36 35 34 33 32 31 30 29 28 27 PGND PGND PGND PGND PGND PGND PGND NC INTVCC INTVCC EXTVCC SGND SW SVIN + * 41 T1 1:N 42 43 44 45 46 47 VIN 48 49 50 51 52 SW SW SW SW SW SW SW PVIN PVIN PVIN PVIN RUN/SS PVIN BOOST SGND PVIN PVIN PVIN PVIN PVIN PVIN PVIN SW NC LTC3609 SGND NC NC VFB ION NC SGND FCB ITH VRNG PGOOD SGND SGND VON 26 25 24 23 22 21 20 19 18 17 16 15 OPTIONAL EXTVCC CONNECTION 5V < VOUT2 < 7V R3 R4 + * + CIN 1 2 3 4 5 6 7 8 SW 9 10 11 12 13 14 3609 F04 SGND Figure 4. Secondary Output Loop and EXTVCC Connection within the LTC3609. The INTVCC pin can supply up to 50mA RMS and must be bypassed to ground with a minimum of 4.7F tantalum or ceramic capacitor. Good bypassing is necessary to supply the high transient currents required by the MOSFET gate drivers. The EXTVCC pin can be used to provide MOSFET gate drive and control power from the output or another external source during normal operation. Whenever the EXTVCC pin is above 4.7V the internal 5V regulator is shut off and an internal 50mA P-channel switch connects the EXTVCC pin to INTVCC. INTVCC power is supplied from EXTVCC until this pin drops below 4.5V. Do not apply more than 7V to the EXTVCC pin and ensure that EXTVCC VIN. The following list summarizes the possible connections for EXTVCC: 1. EXTVCC grounded. INTVCC is always powered from the internal 5V regulator. 2. EXTVCC connected to an external supply. A high efficiency supply compatible with the MOSFET gate drive requirements (typically 5V) can improve overall efficiency. 3. EXTVCC connected to an output derived boost network. The low voltage output can be boosted using a charge pump or flyback winding to greater than 4.7V. The system will start-up using the internal linear regulator until the boosted output supply is available. Soft-Start and Latchoff with the RUN/SS Pin The RUN/SS pin provides a means to shut down the LTC3609 as well as a timer for soft-start and overcurrent latchoff. Pulling the RUN/SS pin below 0.8V puts the LTC3609 into a low quiescent current shutdown (IQ < 30A). Releasing the pin allows an internal 1.2A current source to charge up the external timing capacitor CSS. If RUN/SS has been pulled all the way to ground, there is a delay before starting of about: tDELAY = 1.5V CSS = 1.3s/F CSS 1.2A ( ) 3609f 15 LTC3609 APPLICATIONS INFORMATION When the voltage on RUN/SS reaches 1.5V, the LTC3609 begins operating with a clamp on ITH of approximately 0.9V. As the RUN/SS voltage rises to 3V, the clamp on ITH is raised until its full 2.4V range is available. This takes an additional 1.3s/F during which the load current is folded , back until the output reaches 75% of its final value. After the controller has been started and given adequate time to charge up the output capacitor, CSS is used as a short-circuit timer. After the RUN/SS pin charges above 4V, if the output voltage falls below 75% of its regulated value, then a short-circuit fault is assumed. A 1.8A current then begins discharging CSS. If the fault condition persists until the RUN/SS pin drops to 3.5V, then the controller turns off both power MOSFETs, shutting down the converter permanently. The RUN/SS pin must be actively pulled down to ground in order to restart operation. The overcurrent protection timer requires that the soft-start timing capacitor CSS be made large enough to guarantee that the output is in regulation by the time CSS has reached the 4V threshold. In general, this will depend upon the size of the output capacitance, output voltage and load current characteristic. A minimum soft-start capacitor can be estimated from: CSS > COUT VOUT RSENSE (10 -4 [F/V s]) Generally 0.1F is more than sufficient. Overcurrent latchoff operation is not always needed or desired. Load current is already limited during a short-circuit by the current foldback circuitry and latchoff operation can prove annoying during troubleshooting. The feature can be overridden by adding a pull-up current greater than 5A to the RUN/SS pin. The additional current prevents the discharge of CSS during a fault and also shortens the soft-start period. Using a resistor to VIN as shown in Figure 5a is simple, but slightly increases shutdown current. Connecting a resistor to INTVCC as shown in Figure 5b eliminates the additional shutdown current, but requires a diode to isolate CSS. Any pull-up network must be able to pull RUN/SS above the 4.2V maximum threshold of the latchoff circuit and overcome the 4A maximum discharge current. INTVCC RSS* RUN/SS RSS* D2* RUN/SS VIN 3.3V OR 5V D1 2N7002 CSS CSS 3609 F05 *OPTIONAL TO OVERRIDE OVERCURRENT LATCHOFF (5a) (5b) Figure 5. RUN/SS Pin Interfacing with Latchoff Defeated Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Although all dissipative elements in the circuit produce losses, four main sources account for most of the losses in LTC3609 circuits: 1. DC I2R losses. These arise from the resistance of the internal resistance of the MOSFETs, inductor and PC board traces and cause the efficiency to drop at high output currents. In continuous mode the average output current flows through L, but is chopped between the top and bottom MOSFETs. The DC I2R loss for one MOSFET can simply be determined by [RDS(ON) + RL] * IO. 2. Transition loss. This loss arises from the brief amount of time the top MOSFET spends in the saturated region during switch node transitions. It depends upon the input voltage, load current, driver strength and MOSFET capacitance, among other factors. The loss is significant at input voltages above 20V and can be estimated from: Transition Loss (1.7A-1) VIN2 IOUT CRSS f 3. INTVCC current. This is the sum of the MOSFET driver and control currents. This loss can be reduced by supplying INTVCC current through the EXTVCC pin from a high efficiency source, such as an output derived boost network or alternate supply if available. 3609f 16 LTC3609 APPLICATIONS INFORMATION 4. CIN loss. The input capacitor has the difficult job of filtering the large RMS input current to the regulator. It must have a very low ESR to minimize the AC I2R loss and sufficient capacitance to prevent the RMS current from causing additional upstream losses in fuses or batteries. Other losses, including COUT ESR loss, Schottky diode D1 conduction loss during dead time and inductor core loss generally account for less than 2% additional loss. When making adjustments to improve efficiency, the input current is the best indicator of changes in efficiency. If you make a change and the input current decreases, then the efficiency has increased. If there is no change in input current, then there is no change in efficiency. Checking Transient Response The regulator loop response can be checked by looking at the load transient response. Switching regulators take several cycles to respond to a step in load current. When a load step occurs, VOUT immediately shifts by an amount equal to ILOAD (ESR), where ESR is the effective series resistance of COUT. ILOAD also begins to charge or discharge COUT generating a feedback error signal used by the regulator to return VOUT to its steady-state value. During this recovery time, VOUT can be monitored for overshoot or ringing that would indicate a stability problem. The ITH pin external components shown in Figure 6 will provide adequate compensation for most applications. For a detailed explanation of switching control loop theory see Application Note 76. Design Example As a design example, take a supply with the following specifications: VIN = 5V to 32V (12V nominal), VOUT = 2.5V 5%, IOUT(MAX) = 6A, f = 550kHz. First, calculate the timing resistor with VON = VOUT: 2.5V RON = = 187k (2.4V )(550kHz )(10pF ) and choose the inductor for about 40% ripple current at the maximum VIN: L= 2.5V 2.5V = 1.8H 1- (550kHz )(0.4)(6A ) 32V Selecting a standard value of 1.5H results in a maximum ripple current of: IL = 2.5V 2.5V 1- = 2.4A (550kHz )(1.5H) 12V Next, set up VRNG voltage and check the ILIMIT. Tying VRNG to GND will set the typical current limit to 9A, and tying VRNG to 1.2V will result in a typical current around 14A. CIN is chosen for an RMS current rating of about 5A at 85C. The ceramic output capacitors are chosen for an ESR of 0.002 to minimize output voltage changes due to inductor ripple current and load steps. The ripple voltage is: VOUT(RIPPLE) = IL(MAX) (ESR) = (2.4A) (0.002) = 4.8mV and a 0A to 6A load step will only cause an output change of: VOUT(STEP) = ILOAD (ESR) = (6A) (0.002) = 12mV An optional 22F ceramic output capacitor is included to minimize the effect of ESL in the output ripple. The complete circuit is shown in Figure 6. PC Board Layout Checklist When laying out a PC board follow one of the two suggested approaches. The simple PC board layout requires a dedicated ground plane layer. Also, for higher currents, a multilayer board is recommended to help with heat sinking of power components. * The ground plane layer should not have any traces and it should be as close as possible to the layer with the LTC3609. * Place CIN and COUT all in one compact area, close to the LTC3609. It may help to have some components on the bottom side of the board. * Keep small-signal components close to the LTC3609. * Ground connections (including LTC3609 SGND and PGND) should be made through immediate vias to the ground plane. Use several larger vias for power components. 3609f 17 LTC3609 APPLICATIONS INFORMATION INTVCC CF 0.1F 50V SW 40 39 38 37 36 35 34 33 32 31 30 29 28 27 PGND PGND PGND PGND PGND PGND PGND SVIN INTVCC INTVCC EXTVCC SGND SW NC R2 30.1k 1% VOUT R1 9.53k 1% RON 187k 1% VIN JP1 R5 15.8k CC1 1000pF VIN RF1 1 EXTVCC C4 0.01F CVCC 4.7F 6.3V GND VOUT 2.5V AT 6A 41 COUT1 100F x2 + L1 1.2H SW SW SW SW SW SW SW PVIN PVIN PVIN PVIN RUN/SS PVIN BOOST SGND PVIN PVIN PVIN PVIN PVIN PVIN PVIN SW NC LTC3609 SGND NC NC VFB ION NC SGND FCB ITH VRNG PGOOD SGND SGND VON 26 25 24 23 22 21 20 19 18 17 16 15 42 43 44 45 46 47 GND INTVCC VIN 5V TO 32V VIN CIN 4.7F 50V x2 48 49 50 51 52 RPG1 100k CC2 100pF 1 2 3 4 5 6 7 8 SW 9 10 11 12 13 14 SGND 2 VOUT CVON 0.1F PGOOD INTVCC CIN: MURATA GRM32ER71H475K COUT: MURATA GRM435R60J107M LI: CDEP851R2MC-50 KEEP POWER GROUND AND SIGNAL GROUND SEPARATE. CONNECT AT ONE POINT. INTVCC DB CMDSH-3 SW 3609 F06 CB1 0.22F CSS 0.1F Figure 6. Design Example: 5V to 32V Input to 2.5V/6A at 550kHz * Use a compact plane for the switch node (SW) to improve cooling of the MOSFETs and to keep EMI down. * Use planes for VIN and VOUT to maintain good voltage filtering and to keep power losses low. * Flood all unused areas on all layers with copper. Flooding with copper reduces the temperature rise of power components. Connect these copper areas to any DC net (VIN, VOUT, GND or to any other DC rail in your system). When laying out a printed circuit board without a ground plane, use the following checklist to ensure proper operation of the controller. These items are also illustrated in Figure 7. * Segregate the signal and power grounds. All small signal components should return to the SGND pin at one point, which is then tied to the PGND pin. * Connect the input capacitor(s) CIN close to the IC. This capacitor carries the MOSFET AC current. * Keep the high dV/dT SW, BOOST and TG nodes away from sensitive small-signal nodes. * Connect the INTVCC decoupling capacitor CVCC closely to the INTVCC and PGND pins. * Connect the top driver boost capacitor CB closely to the BOOST and SW pins. * Connect the VIN pin decoupling capacitor CF closely to the VIN and PGND pins. 3609f 18 LTC3609 APPLICATIONS INFORMATION CVCC SW 40 39 38 37 36 35 34 33 32 31 30 29 28 27 PGND PGND PGND PGND PGND PGND PGND INTVCC INTVCC COUT 41 VOUT 42 43 44 45 46 47 48 CIN 49 50 51 52 SW SW SW SW SW SW SW PVIN PVIN PVIN PVIN RUN/SS PVIN BOOST SGND PVIN PVIN PVIN PVIN PVIN PVIN PVIN SW NC LTC3609 EXTVCC SGND SW SVIN NC SGND NC NC VFB ION NC SGND FCB ITH VRNG PGOOD SGND SGND VON 26 25 24 23 22 21 20 19 18 17 16 15 CC2 RC CC1 R1 R2 RON 1 2 3 4 5 6 7 8 9 10 11 12 13 14 DB CB RF CSS 3609 F07 KEEP POWER GROUND AND SIGNAL GROUND SEPARATE. CONNECT AT ONE POINT. Figure 7. LTC3609 Layout Diagram 3609f 19 LTC3609 TYPICAL APPLICATIONS 3.6V Input to 1.5V/6A at 750kHz INTVCC CF 0.1F 50V SW 40 39 38 37 36 35 34 33 32 31 30 29 28 27 INTVCC INTVCC EXTVCC PGND PGND PGND PGND PGND PGND PGND NC SGND SW SVIN R2 60.4k 1% VOUT 26 25 24 23 22 21 20 19 18 17 16 15 RPG1 100k CC2 100pF R5 8.45k CC1 1500pF R1 40.2k 1% RON 113k 1% VIN JP1 VBIAS 5V EXTVCC C4 0.01F CVCC 4.7F 6.3V GND VOUT 1.5V AT 6A 41 COUT1 100F x2 L1 0.5H 42 43 44 45 46 47 VIN CIN 4.7F 50V x2 SW SW SW SW SW SW SW PVIN PVIN PVIN PVIN RUN/SS PVIN BOOST SGND PVIN PVIN PVIN PVIN PVIN PVIN PVIN SW NC LTC3609 SGND NC NC VFB ION NC SGND FCB ITH VRNG PGOOD SGND SGND VON GND INTVCC VIN 3.6V 48 49 50 51 52 1 2 3 4 5 6 7 8 SW 9 10 11 12 13 14 SGND 2 VOUT CVON 0.1F PGOOD INTVCC CIN: MURATA GRM32ER71H475K COUT: MURATA GRM435R60J167M LI: CDEP850R5MC-125 KEEP POWER GROUND AND SIGNAL GROUND SEPARATE. CONNECT AT ONE POINT. INTVCC DB CMDSH-3 SW 3609 TA02 CB1 0.22F CSS 0.1F Transient Response 100 95 IL 5A/DIV EFFICIENCY (%) 90 85 80 75 70 65 20s/DIV LOAD STEP 1A TO 5A VIN = 3.6V VOUT = 1.5V FCB = 0V 3609 TA02b Efficiency vs Load Current VOUT 200mV/DIV 60 55 50 0.01 VIN = 3.6V FREQUENCY = 750kHz 0.1 1 LOAD CURRENT (A) 10 3609 TA02c 3609f 20 LTC3609 TYPICAL APPLICATIONS 5V to 32V Input to 1.2V/6A at 550kHz INTVCC CF 0.1F 25V SW 40 39 38 37 36 35 34 33 32 31 30 29 28 27 INTVCC INTVCC EXTVCC PGND PGND PGND PGND PGND PGND PGND NC SGND SW SVIN R2 60.4k 1% VOUT R1 60.4k 1% RON 182k 1% VIN JP1 R5 8.45k CC1 1500pF VIN RF1 1 EXTVCC C4 0.01F CVCC 4.7F 6.3V GND VOUT 1.2V AT 6A 41 COUT1 100F x2 L1 0.8H 42 43 44 45 46 47 VIN CIN 4.7F 50V x2 SW SW SW SW SW SW SW PVIN PVIN PVIN PVIN RUN/SS PVIN BOOST SGND PVIN PVIN PVIN PVIN PVIN PVIN PVIN SW NC LTC3609 SGND NC NC VFB ION NC SGND FCB ITH VRNG PGOOD SGND SGND VON 26 25 24 23 22 21 20 19 18 17 16 15 R3 0 GND INTVCC VIN 5V TO 32V 48 49 50 51 52 RPG1 100k CC2 100pF 1 2 3 4 5 6 7 8 SW 9 10 11 12 13 14 SGND 2 VOUT CVON 0.1F PGOOD INTVCC C5: TAIYO YUDEN JMK316BJ226ML-T CIN: MURATA GRM32ER71H475K COUT: MURATA GRM435R60J167M LI: CDEP850R8MC-88 KEEP POWER GROUND AND SIGNAL GROUND SEPARATE. CONNECT AT ONE POINT. INTVCC DB CMDSH-3 SW 3609 TA03 CB1 0.22F CSS 0.1F Transient Response 90 IL 5A/DIV EFFICIENCY (%) 85 80 75 70 65 60 20s/DIV LOAD STEP 1A TO 6A VIN = 12V VOUT = 1.2V FCB = 0V 3609 TA02b Efficiency vs Load Current VIN = 12V FREQUENCY = 550kHz VOUT 200mV/DIV 55 50 0.01 0.1 1 LOAD CURRENT (A) 10 3609 TA02c 3609f 21 LTC3609 TYPICAL APPLICATIONS 5V to 32V Input to 1.8V/6A All Ceramic 1MHz INTVCC CF 0.1F 50V SW 40 39 38 37 36 35 34 33 32 31 30 29 28 27 INTVCC INTVCC EXTVCC PGND PGND PGND PGND PGND PGND PGND NC SGND SW SVIN R2 20k 1% VOUT R1 10k 1% RON 102k 1% VIN JP1 R5 5.76k CC1 1500pF VIN RF1 1 EXTVCC C4 0.01F CVCC 4.7F 6.3V GND VOUT 1.8V AT 6A 41 COUT1 100F x2 L1 0.47H 42 43 44 45 46 47 VIN CIN 4.7F x2 SW SW SW SW SW SW SW PVIN PVIN PVIN PVIN RUN/SS PVIN BOOST SGND PVIN PVIN PVIN PVIN PVIN PVIN PVIN SW NC LTC3609 SGND NC NC VFB ION NC SGND FCB ITH VRNG PGOOD SGND SGND VON 26 25 24 23 22 21 20 19 18 17 16 15 GND INTVCC VIN 5V TO 32V 48 49 50 51 52 RPG1 100k CC2 100pF 1 2 3 4 5 6 7 8 SW 9 10 11 12 13 14 SGND 2 PGOOD INTVCC C5: TAIYO YUDEN JMK316BJ226ML-T CIN: MURATA GRM32ER71H475K COUT: MURATA GRM32ER60J107M LI: 1HLP25CZERR80M01 KEEP POWER GROUND AND SIGNAL GROUND SEPARATE. CONNECT AT ONE POINT. INTVCC DB CMDSH-3 SW CB1 0.22F CSS 0.1F VOUT CVON 0.1F 3609 TA04 Transient Response 100 IL 5A/DIV EFFICIENCY (%) 90 80 70 60 50 40 30 20s/DIV LOAD STEP 500mA TO 4A VIN = 12V VOUT = 1.8V FCB = 0V 3609 TA04b Efficiency vs Load Current VOUT 200mV/DIV 20 10 0 10 100 1000 LOAD CURRENT (mA) 10000 3609 TA04c 3609f 22 LTC3609 PACKAGE DESCRIPTION WKG Package 52-Lead QFN Multipad (7mm x 8mm) (Reference LTC DWG # 05-08-1768 Rev O) SEATING PLANE 7.00 BSC A B 0.00 - 0.05 41 40 2.625 REF 2.90 REF 0.50 BSC 52 1 PIN 1 ID 4 PAD 1 CORNER 7 bbb M C A B 3.40 REF 3.90 0.10 2.925 0.10 2.025 0.10 3.20 0.10 3.40 REF 8.00 BSC 33 32 8 9 10 1.00 REF NX b aaa C 2x 4.275 0.10 2.25 0.10 27 0.580 0.10 26 aaa C 2x 14 0.40 0.10 19 1.775 REF 15 0.25 0.05 1.35 0.10 TOP VIEW // ccc C 7.50 0.05 0.90 0.10 9 NX 0.08 C 8 BOTTOM VIEW (BOTTOM METALLIZATION DETAILS) MLP52 QFN REV O 0807 2.90 REF 0.50 BSC 2.625 REF NOTE: 1. DIMENSIONING AND TOLERANCING CONFORM TO ASME Y14.5M-1994 2. ALL DIMENSIONS ARE IN MILLIMETERS, ANGLES ARE IN DEGREES () 3. N IS THE TOTAL NUMBER OF TERMINALS PIN 1 4 3.20 0.10 3.40 REF 2.025 0.10 3.40 REF 2.925 0.10 3.90 0.10 THE LOCATION OF THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION CONFORMS TO JEDEC PUBLICATION 95 SPP-002 5. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY 6. NJR REFER TO NON JEDEC REGISTERED 7 1.00 REF 8.50 0.05 2.25 0.10 4.275 0.10 DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.20mm AND 0.30mm FROM THE TERMINAL TIP. IF THE TERMINAL HAS THE OPTIONAL RADIUS ON THE OTHER END OF THE TERMINAL, THE DIMENSION b SHOULD NOT BE MEASURED IN THAT RADIUS AREA. COPLANARITY APPLIES TO THE TERMINALS AND ALL OTHER SURFACE METALLIZATION DRAWING SHOWN ARE FOR ILLUSTRATION ONLY SYMBOL TOLERANCE 0.15 aaa 0.10 bbb 0.10 ccc 8 9 0.40 0.10 0.25 0.05 1.775 REF 1.35 0.10 PACKAGE OUTLINE RECOMMENDED SOLDER PAD LAYOUT TOP VIEW 3609f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 23 LTC3609 TYPICAL APPLICATION INTVCC CF 0.1F 50V SW 40 39 38 37 36 35 34 33 32 31 30 29 28 27 PGND PGND PGND PGND PGND PGND PGND SVIN INTVCC INTVCC EXTVCC SGND SW NC R2 60.4k 1% VOUT R1 3.16k RON 1% 1M 1% VIN JP1 R5 24.3k CC1 1000pF VIN RF1 1 EXTVCC C4 0.01F CVCC 4.7F 6.3V GND VOUT 12V AT 4A 41 COUT1 180F 16V + L1 4.3H SW SW SW SW SW SW SW PVIN PVIN PVIN PVIN RUN/SS PVIN BOOST SGND PVIN PVIN PVIN PVIN PVIN PVIN PVIN SW NC LTC3609 SGND NC NC VFB ION NC SGND FCB ITH VRNG PGOOD SGND SGND VON 26 25 24 23 22 21 20 19 18 17 16 15 42 43 44 45 46 47 GND INTVCC VIN 14V TO 32V VIN CIN 4.7F x2 48 49 50 51 52 RPG1 100k CC2 100pF 1 2 3 4 5 6 7 8 SW 9 10 11 12 13 14 SGND 2 PGOOD INTVCC CIN: MURATA GRM31CR71H475K COUT: SANYO 16SVP180MX LI: CDEP4R3MC-88 KEEP POWER GROUND AND SIGNAL GROUND SEPARATE. CONNECT AT ONE POINT. INTVCC DB CMDSH-3 SW CB1 0.22F CSS 0.1F INTVCC CVON 0.1F 3609 TA05 Figure 8. 14V to 32V Input to 12V/4A at 500kHz RELATED PARTS PART NUMBER DESCRIPTION LTC3602 LTC3608 LTC3610 LTC3611 LTC3414/ LTC3416 LTC3415 LTC3418 2.5A (IOUT), 3MHz, Synchronous Step-Down DC/DC Converter 18V, 8A (IOUT), 1MHz, Synchronous Step-Down DC/DC Converter 24V, 12A (IOUT), 1MHz, Synchronous Step-Down DC/DC Converter 32V, 10A (IOUT), 1MHz, Synchronous Step-Down DC/DC Converter 4A (IOUT), 4MHz, Synchronous Step-Down DC/DC Converter 7A (IOUT), 1.5MHz, Synchronous Step-Down DC/DC Converter 8A (IOUT), 4MHz, Synchronous Step-Down DC/DC Converter COMMENTS 95% Efficiency, VIN: 4.5V to 10V, VOUT(MIN) = 0.6V, IQ = 75A, ISD <1A, 4mm x 4mm QFN-20, TSSOP-16E Packages 95% Efficiency, VIN: 4V to 18V, VOUT(MIN) = 0.6V, IQ = 900A, ISD <15A, 7mm x 8mm QFN-52 Package 95% Efficiency, VIN: 4V to 24V, VOUT(MIN) = 0.6V, IQ = 900A, ISD <15A, 9mm x 9mm QFN-64 Package 95% Efficiency, VIN: 4V to 32V, VOUT(MIN) = 0.6V, IQ = 900A, ISD <15A, 9mm x 9mm QFN-64 Package 95% Efficiency, VIN: 2.25V to 5.5V, VOUT(MIN) = 0.8V, IQ = 64A, ISD <1A, TSSOP20E Package 95% Efficiency, VIN: 2.5V to 5.5V, VOUT(MIN) = 0.6V, IQ = 450A, ISD <1A, 5mm x 7mm QFN-38 Package 95% Efficiency, VIN: 2.25V to 5.5V, VOUT(MIN) = 0.8V, IQ = 380A, ISD <1A, 5mm x 7mm QFN-38 Package 3609f LT 1208 * PRINTED IN USA 24 Linear Technology Corporation (408) 432-1900 FAX: (408) 434-0507 1630 McCarthy Blvd., Milpitas, CA 95035-7417 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2008 |
Price & Availability of LTC3609
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |